Search results

Hello,putting new bearings on my spindle, and got this far in disassembly. two snap rings are already loose. I have an arbor press but not sure which way to press on it and didn’t want to screw it up Thanks

Hello, I am looking for a rack and gear that will run on a 1/2 to 3/4 inch pipe or tube. The gear would run off a knob to raise and lower an indexing pin. anyone know where to source something like this? Have seen something similar for servo motors, but this will be used as an indexing tool...

Hello, I would like to wire a 24V DC motor for a fishing rod wrapper. I’m going to need a converter, and a speed controller, with reverse capability, and a switch to run either off a foot pedal or continuously off the speed controller. The motor I’m looking at will draw no more than one amp and...

Hello, I would like to wire a DC motor for a fishing rod wrapper. I’m going to need a converter, and a speed controller, with reverse capability, and a switch to run either off a foot pedal or continuously off the speed controller. The motor I’m looking at will draw no more than one amp and 25...

Hello, I’m trying to source these rollers. Not getting them very many hits on Google. Anyone know the name for them? Thanks

Anyone familiar with a screwdriver made for this screw? This is on a Diawa reel Sent from my iPhone using Tapatalk Pro

Can anyone recommend a good auto tool kit to keep in the trunk? I already have plenty of tools in the garage, but was looking for a kit with wrenches, sockets, ratchet, pliers, etc. kind of an emergency kit. Doesn’t have to be Snapon quality, but looking for something that’s not junk. Hopefully...

Horizontal space is at a premium, so I went vertical with my cart, build the hose hangers inside the cart, they stick out about 1/2 inch. Built a junction box so that all the electric cables tuck in down in the bottom and plug in the back of the box, with one plug only to the wall. Rides on...

Anybody familiar with these electric motors, are they pretty reliable? Just noticed spell check ...should be teco Westinghouse

Seems I saw this somewhere, but can’t remember now. Does anyone make a tape that doesn’t leave a gooey mess when it is removed? Thanks Sent from my iPhone using Tapatalk Pro

Does anyone make a three-way valve for high pressure gas? I am going to run two welding tanks into a single line, and use one at a time. I think the tanks are pressurized at about 2500 . These are available but I would prefer a three-way valve, that can handle that kind of pressure Sent...

Any recommendations for an online store that sells radiused square tube and round tube? It is usually hit or miss at my steel supplier. Sent from my iPhone using Tapatalk Pro

I’m looking at getting another shop vacuum, and would appreciate some recommendations. I already have a Milwaukee m18 portable, which is great for cleaning up around the saw, drill, and welding stations, but not so good for cleaning up big areas. I use a blower to clean periodically, but this...

Getting to work on some clamps for the welding table. 1.5 round stock, and 1.5 ID DOM for the collars. The third pic shows a prototype with a pin, but that got bagged to cut costs, and they are just welded in the slot. I’m pleasantly surprised how well they hold, no slip, and you can really...

What’s the best air hose material that will clean off easy and not blacken with time? Thanks Sent from my iPhone using Tapatalk Pro

There is a cordless tungsten grinder “ sharpie DX”, that is sold by arc zone https://www.arc-zone.com/cordless-sharpie-grinder-a-ptgk-dxcl I don’t see this on the Milwaukee website. Is this something made by arc zone with Milwaukee parts? Sent from my iPhone using Tapatalk Pro

I’m looking at needle scalers. Never used one. Are the needles proprietary to make? If I bought an IR, could I go into HF and buy needles for it? Thanks Sent from my iPhone using Tapatalk Pro

My favorite snap on 3/8 ratchet grew legs. I was thinking about replacing it with a nepros. They are about the same price. Are they about the same quality? Sent from my iPhone using Tapatalk Pro

I'm starting to accumulate a lot of leftovers, and thinking about building a storage cart. If you have one can you show a picture? Not sure if I want to go with horizontal or vertical storage. Thanks Sent from my iPad using Tapatalk Pro

How do you get maximum use of your flap disc? This one has plenty of thickness, but no longer cuts well. Do you just have to bear down on it more, as it wears? Sent from my iPhone using Tapatalk Pro